How To Make A Windows 98 Installation Disk

• INTRODUCTION
• REQUIREMENTS
• PREPARE THE USB DRIVE
• INSTALLING WINDOWS 98SE

The instructions below will allow you to add together a Windows 98 ISO file to your Easy2Boot drive and install Win98 to an internal hard disk.

It should besides piece of work for Windows ME.

New eBook on grub4dos is now bachelor. Over 170 pages.

INTRODUCTION

If you lot would like to be able to re-install Windows 98 or Me onto a arrangement that possibly has a broken CD-ROM, and so you tin do then using Easy2Boot.

REQUIREMENTS

Earlier we commencement however, please remember that Win98 is a very sometime Operating Organization and then is quite catchy to install on modern systems.

The 98/Me browser is very old - nearly websites volition not display correctly in any Win98/Me browser, so internet admission is extremely limited!

Check here for a list of compatible mainboards.

Please check the following requirements before you brainstorm!

• The target system must be able to boot from a USB drive (Flash or HDD)
• The target arrangement must take an IDE hard disk bulldoze (SATA drives may not work - set the 'Legacy/IDE' setting in the BIOS setup menu if you lot take a SATA hard drive fitted - do not use 'AHCI')
• Older arrangement BIOSes may accept a 137GB hd limit - installing onto a difficult disk larger than 137GB may cause problems (also using a USB Hard disk larger than 137GB may cause problems - E2B volition warn y'all if this is the case) - see here for more than details.
• Your target organisation will demand 256MB or more than of retention (the ISO contents are copied to RAM) - however, systems with more than 1GB may also cause memory problems.
• You will need a utility to delete some folders from within the Win98SE ISO - eastward.g. Daemon Tools Pro or UltraISO (so you don't lose the kick sectors from the ISO).
• Win98 may not take the correct drivers for your audio, network and graphics devices
• Windows 98 SE ISO (y'all will have to obtain this yourself) - the ISO can be bootable (preferred) or non-bootable. Try hither (OEM Total is bootable) or here.
• (optional) Windows 98 SE 1.44Mb floppy .img image file (y'all will have to obtain this yourself) - only required if the Win98 ISO is not bootable.

If you lot wish to try this by using a Virtual Machine (eastward.g. Oracle Virtual Box), ensure y'all configure it for Windows 98, use a pocket-size amount of memory for Display VGA retentivity and not more than 1GB of system retentivity (RAM). Apply an IDE virtual hd.

PREPARE THE USB DRIVE

1. Make an E2B bootable USB drive from www.easy2boot.com

two. Check that you lot can boot the E2B USB drive on your target organisation - if not then you cannot proceed any further!

3. (optional) Edit the Windows 98 SE ISO file that you accept obtained and leave only the files in the root (pinnacle level) and the \win98 folder.

Save the ISO file. I used Daemon Tools Pro for this. UltraISO also works.

The reason that we need to delete the other folders is that the E2B copy process will fail if there are besides many files.

Also, we don't demand these folders to install Windows 98.

If y'all like, yous can effort the ISO without editing it first, merely it may fail to load or install properly.

4. If the ISO is not bootable (cheque with 7Zip - Open up Annal, look for a [Boot] binder containing a Bootable_1.44M.img file) then you will need to detect and download an MS-DOS floppy disk prototype.

If the ISO does incorporate a bootable 1.44Mb floppy prototype equally [BOOT], you only demand the ISO file and you do not need a separate .IMG file.

4a. If your Win98SE ISO is bootable:

Merely re-create the reduced-size ISO (approx 180MB) to the E2B USB drive \_ISO\MAINMENU folder and rename the file to have the .ISODOS01 file extension

(optional) Create a .txt file of the aforementioned proper noun as the Win98SE ISO containing the bill of fare entry that you want to appear in the E2B Main carte instead of just the name of the ISODOS01 file - e.g.:

title Win98SE Install (ISO)\north Choose 2 Boot from CD-ROM then iii without CD-ROM option ii\n Run FDISK to division the HDD\n And so reboot and run Format.\n Change to drive B: and type Setup to install Win98

This completes the USB bulldoze preparation if your Win98SE ISO was bootable.

4b. If your Win98SE ISO is not bootable:

Copy the reduced-size Win98SE ISO and the .IMG file to the \_ISO\MAINMENU\Win98 folder (yous volition need to make a Win98 folder on the E2B USB drive)

Utilize Notepad to create a new file at \_ISO\MAINMENU\InstWin98SE.mnu with the following contents (change the filenames in bold type to match your filenames):

• title Win98SE Install (ISO+FD IMG)\n Cull not-CDROM option 2\n Run FDISK to sectionalization the HDD\north And then reboot and run Format.\north Modify to drive B: and blazon Setup
• ready ISO=(bd)/_ISO/MAINMENU/Win98/Win98se.iso
• map /_ISO/MAINMENU/Win98/Windows98_se.img (fd0)
• map %ISO% (0xff)
• cat --length=0 %ISO% ;; ready /a LEN=*0x8290 ;; echo Length of %ISO% is %LEN% bytes
• set /a LEN=%LEN%/512
• # Let for PBR sectors etc. - must be FAT16 so over 0x20000
• set /a LEN=%LEN%+0x1000
• if %LEN%<=0x20000 ready /a LEN=0x20000+0
• echo FILE IS %LEN% sectors
• pause --wait=three Drive B: Length=%LEN% sectors
• # call the copy batch file - first parameter is either (fd0) or (fd1) - adjacent parameter is size of virtual drive (0x100000=512MiB)
• call (bd)/%grub%/copyff.g4b (fd1) %LEN%
• suspension --expect=three Please Note: Contents of CD are now on bulldoze B:
• # set number of floppies seen by BIOS - must exist ii if using (fd1) instead of (fd0)
• map (hd0) (hd1)
• map (hd1) (hd0)
• map --hook
• map --floppies=2
• root (fd0)
• chainloader /io.sys || chainloader /kernel.sys || chainloader (0xff)

5. Be certain to run WinContig (RMPrepUSB - Ctrl+F2) to make all the files contiguous.

You should at present accept a bootable USB drive with which can install Win98SE.

INSTALLING WINDOWS 98SE

1. Kick from the USB E2B drive on the target system.

Select the .isodos01 file (or the Win98SE Install carte du jour entry) and run it.

If you encounter some error letters as the files are copied to retentiveness, this is normally because the ISO contains files with long filenames - these are not required for the install process then won't cause a trouble.

Note that Win98 will brand the starting time hard disk partition Active and MS-DOS bootable. Therefore the first internal difficult disk volition exist modified by this process fifty-fifty if y'all install Win98 to a different hard disk or partition!

2. If yous see a message to kicking from the Difficult Disk or CD-ROM, choose the 'Kicking from CD-ROM' pick. Note: After 10 seconds it may automatically try to boot from the difficult drive - so picket for the menu - don't walk away!

3. When you see a bulletin like that below, choose Option three to boot without CD-ROM back up:

4. Y'all should now be at the MS-DOS A:\> prompt.

We need to format the target organization'southward bulldoze as FAT32.

Blazon FDISK and press the ENTER key and answer 'Y' to the questions about large deejay back up.

Now select selection v and check that Disk 1 is the drive that yous want to install Win98 onto.

If it is not and so be warned that if you proceed, the Win98 Setup process may make kicking loader changes to Disk one anyway as information technology will care for information technology as the Win98 boot bulldoze even if you later choose to install Win98 to a different drive volume!

5. Press <ESC> to return to the primary FDISK Options menu and apply the bill of fare to create a DOS Principal bootable partition on Deejay one.

When this has been created, y'all must reboot once again from the Win98SE ISO using E2B exactly as before (repeat steps 1-4 above).

Note: FDISK may exist sometime and may not piece of work with large hard drives properly! In 1998, all hard disks were IDE\ATAPI (non SATA) and were smaller than 137GB!

Y'all may have problems if your hard disk is larger than 137GB. FDISK may report 'weird' sizes.

vi. Now we can format the new sectionalisation. Run FDISK again and choose Selection 5 again - cheque that Bulldoze C: is on the target bulldoze (we don't desire to format our USB drive!).

If all looks OK, quit FDISK and type

B:\Win98\FORMAT C: /q

to format the drive. (on Windows ME, format.com volition be in the B:\Win9x binder).

vii. Now we are set up to install Windows 98 to the blank, freshly formatted (FAT32) drive C:.

At the MS-DOS command prompt, blazon B: and printing the ENTER key to switch to the B: drive.

At present type SETUP so press the ENTER key. This starts the Windows install process.

If yous get an error about a TEMP folder, type the following commands to make Setup use a folder on the B: drive equally a temporary binder:

mkdir B:\TEMP

setup /T:b:\temp

Use C:\Windows as the install binder.

When requested to make Startup (floppy) Deejay, click Next and so Cancel.

8. The Win98 Setup process will restart several times - you tin can remove the E2B USB drive at this indicate so that it reboots directly from the internal hard deejay.

If you lot boot from the E2B USB central (e.g. if using a VM) then just press F7 in the E2B card to boot from the internal hard disk again.

I successfully used a Win98 cardinal BPKBQ-?????-?????-?????-28FW3 afterward the first restart of a Retail Win98SE install (Google for it!).

Unofficial English Win98SE Service Pack here.

If you find your E2B USB drive no longer boots to the E2B menu, endeavor RMPrepUSB - Install grub4dos - MBR=Y to set it.

Source: https://rmprepusb.com/tutorials/117-install-windows-98se-me-from-an-iso-file-on-an-easy2boot-usb-drive-2/

Posted by: blacksuall1971.blogspot.com

Share this post